Detector Supplies / GC Accessories / Supplies & Accessories / Home - Restek Chromatography Products and Solutions

Detector Supplies

Products
ETP Electron Multipliers for Mass Spectrometry Air stable. 2-year shelf life guarantee. Discrete dynode design results in extended operating life. View Product Information
MSD Source Nut 1.2 mm nut bore permits easy removal of ferrules with a standard tapered-needle file (cat.# 20106). Made of brass to prevent thread-stripping on the transfer line. Design enhances ease of threading onto the transfer line and improves overall lifetime. View Product Information
EZ No-Vent^® GC Column-Mass Spectrometer Connector for Agilent GCs with 5971/5972, 5973, or 5975 GC/MS Change GC/MS columns in minutes without venting—100 µm transfer line maintains vacuum and eliminates the need to vent. Easy to install and maintain—no special tools or plumbing required. Gold-plated body for inertness. High-temperature polyimide ferrules eliminate leaks at the problematic transfer line fitting. Lower cost than other “no-vent” fittings. View Product Information
Inland 45 Pump Oil Recommended for most mass spectrometers. Ease at cold start. Low vapor pressure 10^-7 torr. Nontoxic and noncorrosive. Compatible with buna-N, neoprene, and Viton® seals. Optimum vacuum pump performance. Lowest mass spectrometer background. Recommended for optimum mass spec performance. View Product Information
MSD Conversion Fitting A flat, soft aluminum sealing ring deforms and butt-seals against the MSD interface. A standard Vespel® ferrule seals the column and 1/16-inch stainless steel nut. Fitting is constructed of nickel-plated brass for longevity and softness. Use any standard Vespel® or Vespel®/graphite 1/16-inch ferrule. Includes a 1/16-inch stainless steel nut and two replacement sealing rings. Order ferrules separately. Improved design reduces chance of leaks. View Product Information
EZ No-Vent^® GC Column-Mass Spectrometer Connector for Shimadzu QP 2010 & QP 2010 Plus Change GC/MS columns in minutes without venting—100µm transfer line maintains vacuum and eliminates the need to vent. Easy to install and maintain—no special tools or plumbing required. Gold-plated body for inertness. High-temperature aluminum ferrules eliminate leaks at the transfer line fitting. Lower cost than other “no-vent” fittings. Can be used on Shimadzu QP 2010 and QP 2010 Plus mass spectrometers. View Product Information
GC/MS Cleaning Kit Poor sensitivity, loss of sensitivity at high masses, or high multiplier gain during an auto tune are all indicators that your mass spectrometer source may need to be cleaned. Restek has assembled all of the necessary components for cleaning and polishing your ion source. View Product Information
Gold Tip Transfer Line For use with Agilent 5971/5972 MS Systems. Gold-plated for inertness. Meets or exceeds original manufacturer's performance. View Product Information
EZ No-Vent^® GC Column-Mass Spectrometer Connector for Thermo Scientific Focus DSQ GC Mass Spectrometers Change GC/MS columns in minutes without venting—100 µm transfer line maintains vacuum and prevents venting. Easy to install and maintain—no special tools or plumbing required. Gold-plated body for inertness. High-temperature polyimide ferrules eliminate leaks at the problematic transfer line fitting. Lower cost than other “no-vent” fittings. View Product Information
EZ No-Vent^® GC Column-Mass Spectrometer Connector for Varian Saturn 2000 Series Mass Spectrometers Change GC/MS columns in minutes without venting—100 µm transfer line maintains vacuum and prevents venting. Easy to install and maintain—no special tools or plumbing required. Gold-plated body for inertness. High-temperature polyimide ferrules eliminate leaks at the problematic transfer line fitting. Lower cost than other “no-vent” fittings. View Product Information
Heater/Sensor Assembly for Agilent 6850/6890/7890 GCs Use with FID, TCD, NPD, and split/splitless inlets. Meets or exceeds original manufacturer’s performance. View Product Information
FID Maintenance Kits for Agilent GCs Include the most common consumable GC supplies and tools. All parts meet or exceed performance of instrument manufacturer’s parts. Parts list makes reordering easy. View Product Information
ETP Electron Multipliers for Mass Spectrometry for Thermo Finnigan TRACE DSQ, DSQII, and Polaris Q GC/MS Air stable. 2-year shelf life guarantee. Discrete dynode design results in extended operating life. View Product Information
FID Jet for Thermo Scientific TRACE and Focus GCs Meets or exceeds original manufacturer's performance. View Product Information
Transfer Line Reducing Kit for Thermo Scientific TRACE and Focus DSQ Mass Spectrometers Meets or exceeds original manufacturer's performance. View Product Information
FID Collector Housing Kits for Agilent GCs Meets or exceeds original manufacturer's performance. Available for Agilent 5890, 6890, or 7890 GCs. View Product Information
FID Jet Removal Tool for Agilent 5890/6890/6850/7890 FIDs Securely grips jet in socket for easy removal or installation. Unique, ergonomic handle—easy to hold. View Product Information
Spanner Wrench for Agilent 5890/6890/6850/7890 FID Collector Assemblies Easily remove the nut from the FID collector without damaging the nut. Unique, ergonomic handle—easy to grip. Fits all instrument models. View Product Information
FID Capillary Column Adaptor for PerkinElmer Auto SYS XL Made of high-quality stainless steel. Meet or exceed original manufacturer's performance. View Product Information
FID Replacement Parts for PerkinElmer Auto SYS XL and Clarus 500 Made of high-quality stainless steel. Meet or exceed original manufacturer's performance. View Product Information
FID Base Weldment for Agilent GCs Meets or exceeds original manufacturer's performance. Includes brass nut. Available for Agilent 5890, 6850, or 6890 GCs. View Product Information
FID Collector Mount for Agilent GCs Meets or exceeds original manufacturer's performance. Available for Agilent 5890, 6890, or 7890 GCs. View Product Information
Ion Source Cleaning Powder Use this aluminium oxide powder to clean surfaces that contact the sample or ion beam when you encounter poor sensitivity and inadequate abundances at high masses. View Product Information
Rough Pump Oil #19 for MSD Pumps, Oil Vacuum Pump Formulated from crude oil stocks known for their durability and line lubricating qualities. Use in Agilent 5973/5972/5971 and GCD mass spec systems, or in other manufacturers’ MSD systems that require rough pump oil. Under average use, the oil in the foreline rough pump should be replaced every six months. View Product Information
Heater Cartridge & Platinum Resistance Thermometer (PRT) Sensor for Agilent 5890 GCs Use with 5890 FID and split/splitless weldments. Meets or exceeds original manufacturer's performance. View Product Information
Capillary Installation Gauge for Agilent 5973/5975 MS Seats ferrules onto column for consistent installations. Made from high-quality stainless steel. View Product Information
FID Collector Assembly Kit for Agilent 6890/6850/7890 GCs Constructed of high-quality stainless steel. Meets or exceeds original manufacturer's performance. Individual replacement parts available. View Product Information
Cleaned PTFE Transfer Lines for ELCDs We stringently clean our ELCD PTFE transfer lines with an HCl solution to remove any contaminants, then rinse with methanol. Convenient 6.5-inch precut pieces directly interface the nickel reaction tube and conductivity cell in Tracor, Tremetrics, O.I., and many other ELCDs. View Product Information
Photoionization (PID) Lamps Model 108-10.0/10.6 offers both 10.0 and 10.6 eV potential, has a 0.781″ base diameter, and is used in Tracor, OI, and Baseline instruments. Model 103 has a 1.375″ base and is used in HNU and SRI detectors. Model 108-BTEX lamp’s higher output makes it ideal for detection of BTEX compounds. View Product Information
1/16-Inch Vespel^®/Graphite Sealing Ring Replacement Accesories for Hall 1000 Installs onto the nickel reaction tube after the screw. Easily compresses on the reaction tube to provide a leak-tight seal and prevent detector oxidation. View Product Information
ELCD Nickel Reaction Tube Nut for Hall 1000 High-quality stainless steel ELCD nut mounts nickel reaction tube into ELCD. View Product Information
ELCD Nickel Reaction Tubes for Hall 1000 Pretreated for maximum sensitivity. Quality-controlled for reliability. Available for many popular models. To replace these instrument part numbers -- Tremetrics # 117459-0003, Varian # 00-997625-12, PerkinElmer # N660-1072, or Shimadzu # 220-90435-00 -- order Restek cat. # 21581. To replace this instrument part number -- O.I. Analytical # 260323 -- order Restek cat. # 21582. View Product Information
FID Gauge Pack for Agilent 5890 GCs Pressure regulators and gauges for air & hydrogen. 1/8-inch bulkhead allows easy hookup to instrument. Rated for inlet pressures to 250 psi (1,724 kPa). Rated for outlet pressures of 0 to 60 psi (0-414 kPa). View Product Information
FID/Injector Cleaning Kit Use Restek’s Cleaning Kit with ANY injection port! View Product Information
ECD/FID Dual-Purpose Make-Up Gas Kit for Agilent 5890 GCs Kit includes: replacement fitting, 1/4″ nut, Vespel/graphite ferrule, 1/16″ nut, 0.4 mm ID graphite ferrule, Siltek treated guide View Product Information
Packed Column FID Replacement Jets for Agilent 5890/6890/6850 GCs 0.018-inch ID jets: Used for most general-purpose packed column applications. 0.030-inch ID jets: For packings that exhibit high bleed and that frequently clog the tip of smaller 0.018-inch jets. View Product Information
Capillary Dedicated FID Replacement Jet for Agilent 6890/6850/7890 GCs Available in standard, high-temperature, or Siltek® treated high-performance versions. View Product Information
Capillary Adaptable FID Replacement Jet for Agilent 5890/6890/6850 GCs Available in standard or Siltek® treated high-performance versions. View Product Information
FID/NPD Capillary Adaptor Fitting for Agilent 5890/6890/6850 GCs High-quality stainless steel construction. Meets or exceeds original manufacturer's performance. View Product Information
FID/NPD Adaptor Fitting Easy to use, sturdy, compact stainless steel fitting. 1/16-inch nut uses standard graphite or Vespel®/graphite ferrules. Wrench pad won’t turn when installing a capillary column. Includes 1/4- and 1/16-inch stainless steel nuts, and 1/4-inch Vespel® and 0.4mm ID graphite ferrules. View Product Information
Injector/Detector Plug Nuts Use to cap off an injector to isolate leaks. Use to cap off a detector for thermal cleaning. Use to check a detector or make-up gas flow rate. Use to cap off a detector and prevent hydrogen from accidentally diffusing into the oven from an unused detector base. View Product Information
FID Flow Measuring Adaptor for Agilent 5890/6890/6850/7890 GCs Makes setting flows easy. Meets or exceeds original manufacturer's performance. View Product Information
FID Collector Assembly Kit for Agilent 5890 GCs Constructed of high-quality stainless steel. Meets or exceeds original manufacturer's performance. Individual replacement parts available. View Product Information
Stainless Steel Jet Reamers A great tool for cleaning detector jets or removing stuck ferrules from other small orifices. Serrated design is optimal for removing silica deposits and other contaminants. View Product Information
ECD/Micro ECD Liners Agilent-Style

Detector Supplies

Narrow your results:

for Mass Spectrometry

for Agilent GCs with 5971/5972, 5973, or 5975 GC/MS

for Shimadzu QP 2010 & QP 2010 Plus

for Thermo Scientific Focus DSQ GC Mass Spectrometers

for Varian Saturn 2000 Series Mass Spectrometers

for Agilent 6850/6890/7890 GCs

for Agilent GCs

for Thermo Finnigan TRACE DSQ, DSQII, and Polaris Q GC/MS

for Thermo Scientific TRACE and Focus GCs

for Thermo Scientific TRACE and Focus DSQ Mass Spectrometers

for Agilent GCs

for Agilent 5890/6890/6850/7890 FIDs

for Agilent 5890/6890/6850/7890 FID Collector Assemblies

for PerkinElmer Auto SYS XL

for PerkinElmer Auto SYS XL and Clarus 500

for Agilent GCs

for Agilent GCs

for MSD Pumps, Oil Vacuum Pump

for Agilent 5890 GCs

for Agilent 5973/5975 MS

for Agilent 6890/6850/7890 GCs

Replacement Accesories for Hall 1000

for Hall 1000

for Hall 1000

for Agilent 5890 GCs

for Agilent 5890 GCs

for Agilent 5890/6890/6850 GCs

for Agilent 6890/6850/7890 GCs

for Agilent 5890/6890/6850 GCs

for Agilent 5890/6890/6850 GCs

for Agilent 5890/6890/6850/7890 GCs

for Agilent 5890 GCs