Other Inlet Supplies / GC Accessories / Supplies & Accessories / Home - Restek Chromatography Products and Solutions

Other Inlet Supplies

Products
Flip Seal™ Dual Vespel^® Ring Inlet Seals Restek Innovation! Patented. Reversible Flip Seal™ Inlet Seal—Same Cost, Twice the Lifetime New reversible Flip Seal™ inlet seals from Restek last twice as long as other inlet seals. Simply use—flip—then use again. The reversible design doubles the number of analyses you get per seal. Same easy sealing as Dual Vespel® Ring Inlet Seals—no extra washer needed. Maximum transfer of analytes to column, due to highly inert gold or Siltek® surface. View Product Information
Dual Vespel^® Ring Inlet Seals Washerless, leak-tight seals for Agilent GCs Our patented Dual Vespel® Ring Inlet Seal greatly improves injection port performance—it stays sealed, even after repeated temperature cycles, without retightening the reducing nut! This seal features two soft Vespel® rings, one embedded in its top surface and the other embedded in its bottom surface. These rings eliminate the need for a washer, and ensure very little torque is needed to make a leak-tight seal. Technical Article: Dual Vespel® Ring Inlet Seals: Washerless, Leak-Tight Seals for Agilent GCs View Product Information
Viton^® O-Rings for Agilent GCs Fit split (6.3 mm OD) or splitless (6.5 mm OD) liners. View Product Information
Inlet Maintenance Kit for Agilent GCs Includes the most common consumable GC supplies and tools. All parts meet or exceed performance of instrument manufacturer’s parts. Parts list makes reordering easy. View Product Information
Capillary Column Nuts for Agilent 5890/6890/7890 GCs Available in brass or stainless steel. View Product Information
Finger-Tight Capillary Column Nuts Allow wrench-free column installations. Work with standard or compact (Agilent-style) ferrules. Made from high-quality stainless steel. View Product Information
Finger-Tight Capillary Column Nuts Rapidly tighten without wrenches; avoid stripped threads. Either version can be used with 0.25, 0.32, or 0.53 mm ID columns. View Product Information
Injector Wrench for Agilent 5890/6890/6850 GCs Use to remove the septum nut and weldments during GC maintenance. Use the smaller end to remove the septum nut. Use the larger end to tighten the split/splitless weldment nut. High-quality stainless steel construction. Meets original equipment performance. View Product Information
Septum Nuts for use with Agilent 5890/6890/6850/7890 Split/Splitless Injectors Needle guide allows easy penetration and prevents septum coring. Manual injection septum nut allows use of 26-gauge needles for on-column injections. Made of high-quality stainless steel. View Product Information
Septum Nut Removal Tool for Agilent 5890/6890/6850/7890 GCs Easily remove the septum nut without touching the heated nut—no more burned fingers! Unique, ergonomic handle—easy to grip. Nut remains in tool for quick reattachment. View Product Information
1/16-Inch Capillary Inlet Adaptor Fitting Kit (Split/splitless fitting for capillary columns) 1/16-inch split/splitless fitting that accepts standard capillary ferrules. Easier to install capillary columns because the nut protrudes farther from the insulated injection port chamber. Same column insertion depth as the original manufacturer's equipment. Kit includes adaptor fitting, capillary nut, gold plated 0.8 mm ID Dual Vespel® Ring Inlet Seal, and one 0.4 mm ID ferrule. View Product Information
Viton^® O-Rings for Shimadzu 17A, 2010, and 2014 GCs
Dual Vespel^® Ring Cross-Disk Inlet Seals for Agilent GCs Ideal for high-flow split applications. Washerless, leak-tight seals. View Product Information
Fixing Nut for Capillary Column for Split/Splitless Injector on Thermo Scientific TRACE, 8000, 8000 TOP & Focus SSL Made of high-quality stainless steel. View Product Information
Silver Seals for Thermo Scientific TRACE, 8000, 8000 TOP & Focus SSL
Injector Adaptor for PerkinElmer Auto SYS XL Made of high-quality stainless steel. Meet or exceed original manufacturer's performance. Siltek® treated version available for increased inertness. View Product Information
Restek Enhanced Capillary Nut for Shimadzu 17A, 2010, and 2014 GCs Restek’s design eliminates the slot, increasing lifetime and durability. Meets or exceeds original manufacturer's performance. View Product Information
Viton^® O-Rings for PerkinElmer PSS Injector
Silicone O-Rings for PerkinElmer Auto SYS XL or Clarus with CAP Injector
Capillary Nut for Shimadzu 17A, 2010, and 2014 GCs Meets original manufacturer's performance. View Product Information
Liner Seals for Varian 1078/1079 GCs
Inlet Liner Seals for Varian 1177 Injectors Meets or exceeds original manufacturer's performance. View Product Information
Graphite Sealing Ring for Thermo Scientific TRACE, 8000, 8000 TOP & Focus SSL Instruments
Siltek^® Treated Inlet Support Springs for Varian 1075/1077 Split Injectors Siltek® treated to eliminate sample adsorption. View Product Information
Capillary Nuts for Varian GCs Choose brass or stainless steel construction. View Product Information
Heater Block for Agilent 6850/6890/7890 GC Split/Splitless Injector Meets or exceeds original manufacturer's performance. View Product Information
High Temperature O-Rings for Agilent GCs Usable to 350 °C inlet temperature. Fits split (6.3 mm OD) and splitless (6.5 mm OD) liners. View Product Information
Accessories for ATAS LINEX DMI System
PTV Inlet Adaptor Kit for Gerstel CIS 3 and CIS 4 PTV Inlets Meets original manufacturer's performance. Includes inlet adaptor, silver PTV seal, and slotted capillary nut. View Product Information
Inlet Adaptor Kit for Dual Column Installation for Agilent Capillary Injectors (Split/splitless fitting for capillary columns) 1/16-inch split/splitless fitting that accepts standard, two-hole capillary ferrules. Easier to install capillary columns due to the nut protruding farther from the insulated injection port chamber. Same column insertion depth as the original manufacturer's equipment. Kit includes adaptor fitting, 1/16″ capillary nut, gold-plated 1.2 mm ID Dual Vespel® Ring Inlet Seal, one 0.4 mm ID two-hole ferrule, and one 0.5 mm ID two-hole ferrule. View Product Information
Hot Swap Capillary Column Nuts No more burned fingers! No more downtime waiting for injector parts to cool down. View Product Information
The Claw and The Claw Holder Kit Easily removes hot liners from injection ports. 4 mL vials (not included) can be replaced when dirty. View Product Information
Gold-Plated Liner Cap for Split/Splitless Injector on Thermo Scientific TRACE, 8000, 8000 TOP & Focus SSL
Nut for Terminal Fitting for Thermo Scientific TRACE GCs
Septum Cap for Split/Splitless Injector on Thermo Scientific TRACE, 8000, 8000 TOP & Focus SSL
Make Life Easier (MLE) Capillary Tool Kit for PerkinElmer GCs Everything you need in one complete kit! View Product Information
Make Life Easier (MLE) Capillary Tool Kit for Varian GCs Everything you need in one complete kit! View Product Information
Make Life Easier (MLE) Capillary Tool Kit for Thermo Scientific GCs Everything you need in one complete kit! View Product Information
Make Life Easier (MLE) Capillary Tool Kit for Shimadzu GCs Everything you need in one complete kit! View Product Information
Make Life Easier (MLE) Capillary Tool Kit for Agilent GCs Everything you need in one complete kit! View Product Information
Replacement Viton^® O-Rings for use with the Agilent Flip Top Inlet Sealing System
Capillary Installation Gauge for Shimadzu 17A, 2010, & 2014 GCs Seats ferrule* onto column for consistent installations. Prevents crushed column ends. Made from high-quality stainless steel. View Product Information
Capillary Installation Gauge for Varian GCs for use with 1/16″ ferrules Seats ferrule* onto column for consistent installations. Prevents crushed column ends. Made from high-quality stainless steel. View Product Information
Liner Cap Removing Tool for Thermo Scientific GCs: Focus GC / TRACE GC / Ultra/TRACE GC x GC Easily loosens the liner cap from the injector. Unique, ergonomic handle—easy to grip. View Product Information
Adapters for Capillary Columns on Thermo Scientific TRACE and Focus SSL Use same installation distance as manufacturer's adaptors. Made of high-quality stainless steel. Siltek® treated version available for additional inertness. View Product Information
Capillary Installation Gauge for Thermo Scientific TRACE and Focus SSL (M4 Ferrules) Seats ferrule* onto column for consistent installations. Prevents crushed column ends. Made from high-quality stainless steel. View Product Information
Heater Block Retaining Nuts for Agilent GC Split/Splitless Injectors Aluminum construction. Meet or exceed manufacturer's performance. View Product Information
EPC Test Kit for Agilent 6890 GCs Kit includes 3 O-rings, 2 plugs, 1 mounting screw and 1 test block. View Product Information
Graphite O-Rings for Shimadzu 2010, and 2014 GCs
Septum Nut for Shimadzu 17A, 2010, and 2014 GCs One piece design for ease of installation and removal. Made of clear anodized aluminum and high-quality stainless steel. View Product Information
Graphite O-Rings for PerkinElmer Auto SYS XL or Clarus GCs with PSS Injector
Injector Wrench for Shimadzu 17A, 2010, and 2014 GCs Designed specifically for removing Shimadzu injection ports. High-quality stainless steel construction. View Product Information
Heat Sink for Agilent 5890 GC Split/Splitless Injector Meets or exceeds original manufacturer’s performance. View Product Information
Viton^® O-Rings for Apex Liners
Liner Seals for CIS4 and PTV
Heater Cartridge & Platinum Resistance Thermometer (PRT) Sensor for Agilent 5890 GCs Use with 5890 FID and split/splitless weldments. Meets or exceeds original manufacturer's performance. View Product Information
Capillary Installation Gauge for Agilent 5973/5975 MS Seats ferrules onto column for consistent installations. Made from high-quality stainless steel. View Product Information
Injection Port Repair Tool for Agilent Split/Splitless Injection Ports Remove contaminants, achieve a better seal. Cleans critical inlet seal areas. View Product Information
O-Rings For Agilent GCs. Stable to 200°C. Will not crack or melt. Softer and easier to use than graphite. View Product Information
Inlet Liner Seals for Thermo Scientific TRACE PTV
Rethreading Tool for Agilent Split/Splitless Injection Ports Repair worn or damaged threads in injection ports, fittings, etc. Built-in guide to prevent cross-threading. View Product Information
Inlet Liner Packing Tool Position wool reproducibly every time. Accurate to a specific, measured depth. Can be used with all manufacturer's liners. View Product Information
Inlet Liner Removal Tool Easily remove liner from injector—no more burned fingers. Made from high-temperature silicone. Won’t chip or crack the liner. View Product Information
Capillary Installation Gauge for Agilent GCs Seats graphite* ferrules onto column for consistent installations. Prevents crushed column ends. Made from high-quality stainless steel. View Product Information
CarboFrit^® Puller/Inserter Tool Hook end for removing CarboFrit® inserts. Bent end (90°) for inserting CarboFrit® inserts. View Product Information
Backpressure Gas Regulator Capillary GC inlet systems have backpressure regulators to maintain a constant upstream pressure and rapidly respond to catastrophic leaks. The 0–60 psig (0-414 kPa) operating range is sufficient to operate a 105 m, 0.25 mm ID column at its optimum flow rate. View Product Information
Injector Nut Kit for Shimadzu 17A, 2010, and 2014 GCs Includes 17A injector nut, 0.4 mm graphite ferrule, and 1/16-inch stainless steel capillary nut. View Product Information
Graphite O-Rings for Agilent and Varian 1177 Injectors Excellent thermal stability at injection port temperatures up to 450 °C! View Product Information
Injector/Detector Plug Nuts Use to cap off an injector to isolate leaks. Use to cap off a detector for thermal cleaning. Use to check a detector or make-up gas flow rate. Use to cap off a detector and prevent hydrogen from accidentally diffusing into the oven from an unused detector base. View Product Information
Siltek^® Septum Packed Purge Port Weldment for Agilent 5890 GCs Siltek® treatment makes weldment inert and eliminates adsorption of sensitive compounds (e.g., DDT and Endrin). Order Viton® O-rings and appropriate septa separately. View Product Information
1/8-Inch Capillary Inlet Adaptor Fitting Kit (Split/splitless fitting for 0.53 mm ID capillary columns) 1/8-inch split/splitless fitting accepts standard two-hole capillary ferrules and a standard 1/8-inch nut. Makes column installation easy due to the nut protruding farther from the insulated injection port chamber. The column insertion depth is the same as the original equipment. Kit includes adaptor fitting, capillary nut, stainless steel inlet seal, washer, and one 0.8 mm ID two-hole ferrule. Use recessed gooseneck liners with this adaptor. View Product Information
Direct Replacement Reducing Nut Made from high-quality stainless steel. Meets original manufacturer's equipment performance. View Product Information
Replacement Chemical Traps for Agilent GCs Easy to install. Attach to same fittings as original manufacturer's equipment. Built-in frits retain fine particles; adsorbents remove both moisture and hydrocarbons. View Product Information
60 psig Backpressure Regulator Kit for Agilent GCs Increase the versatility of your Agilent 5890 GC by replacing the existing 30 psig (207 kPa) backpressure regulator and gauge with our 60 psig (414 kPa) regulator. Enables you to use longer 60 m and 105 m columns as well as shorter 10 m columns. Includes complete instructions. View Product Information
Cross-Disk Inlet Seals for Agilent GCs Ideal for high-flow split applications on Agilent 5890 GCs. All seals include washers. View Product Information
Replacement Inlet Seals for Agilent GCs Siltek® treatment provides inertness similar to fused silica. All seals include washers. View Product Information
Mini Wool Puller/Inserter Insert and remove wool plugs easily. Order a spare pack so you’ll always have one available. View Product Information
Septum Puller Use hooked end for removing septa and O-rings; pointed end works well for removing stuck ferrules or debris. Keep several on hand in your laboratory—can be used in many different ways. View Product Information
Silver PTV Seals for Agilent 6890 GCs
Septa Holder Kits for Thermo Scientific TRACE, 8000, 8000 TOP & Focus SSL Includes septum support and holder. Made from high-quality stainless steel. Silcosteel®-AC treated version helps with septum removal. View Product Information
Replacement Inlet Seal Washers

Other Inlet Supplies

Narrow your results:

Washerless, leak-tight seals for Agilent GCs

for Agilent GCs

for Agilent GCs

for Agilent 5890/6890/7890 GCs

for Agilent 5890/6890/6850 GCs

for use with Agilent 5890/6890/6850/7890 Split/Splitless Injectors

for Agilent 5890/6890/6850/7890 GCs

(Split/splitless fitting for capillary columns)

for Shimadzu 17A, 2010, and 2014 GCs

for Agilent GCs

for Split/Splitless Injector on Thermo Scientific TRACE, 8000, 8000 TOP & Focus SSL

for Thermo Scientific TRACE, 8000, 8000 TOP & Focus SSL

for PerkinElmer Auto SYS XL

for Shimadzu 17A, 2010, and 2014 GCs

for PerkinElmer PSS Injector

for PerkinElmer Auto SYS XL or Clarus with CAP Injector

for Shimadzu 17A, 2010, and 2014 GCs

for Varian 1078/1079 GCs

for Varian 1177 Injectors

for Thermo Scientific TRACE, 8000, 8000 TOP & Focus SSL Instruments

for Varian 1075/1077 Split Injectors

for Varian GCs

for Agilent 6850/6890/7890 GC Split/Splitless Injector

for Agilent GCs

for ATAS LINEX DMI System

for Gerstel CIS 3 and CIS 4 PTV Inlets

(Split/splitless fitting for capillary columns)

for Split/Splitless Injector on Thermo Scientific TRACE, 8000, 8000 TOP & Focus SSL

for Thermo Scientific TRACE GCs

for Split/Splitless Injector on Thermo Scientific TRACE, 8000, 8000 TOP & Focus SSL

for PerkinElmer GCs

for Varian GCs

for Thermo Scientific GCs

for Shimadzu GCs

for Agilent GCs

for use with the Agilent Flip Top Inlet Sealing System

for Shimadzu 17A, 2010, & 2014 GCs

for Varian GCs for use with 1/16″ ferrules

for Thermo Scientific GCs: Focus GC / TRACE GC / Ultra/TRACE GC x GC

on Thermo Scientific TRACE and Focus SSL

for Thermo Scientific TRACE and Focus SSL (M4 Ferrules)

for Agilent GC Split/Splitless Injectors

for Agilent 6890 GCs

for Shimadzu 2010, and 2014 GCs

for Shimadzu 17A, 2010, and 2014 GCs

for PerkinElmer Auto SYS XL or Clarus GCs with PSS Injector

for Shimadzu 17A, 2010, and 2014 GCs

for Agilent 5890 GC Split/Splitless Injector

for Apex Liners

for CIS4 and PTV

for Agilent 5890 GCs

for Agilent 5973/5975 MS

for Agilent Split/Splitless Injection Ports

for Thermo Scientific TRACE PTV

for Agilent Split/Splitless Injection Ports

for Agilent GCs

for Shimadzu 17A, 2010, and 2014 GCs

for Agilent and Varian 1177 Injectors

for Agilent 5890 GCs

(Split/splitless fitting for 0.53 mm ID capillary columns)

for Agilent GCs

for Agilent GCs

for Agilent GCs

for Agilent GCs

for Agilent 6890 GCs

for Thermo Scientific TRACE, 8000, 8000 TOP & Focus SSL