Your web browser will no longer be supported by Restek.com as of 30 June 2021.
To avoid any interruption in access or functionality, install a current-generation web browser now. Learn more.

Phospholipid and Protein Removal in One Simple SPE Process Prevents Matrix-Based Signal Suppression

  • Resprep PLR SPE removes both proteins and phospholipids in one easy, high-efficiency procedure.
  • Avoid signal suppression by removing interfering phospholipids from the sample matrix.
  • No method development—straightforward and effective sample preparation for acids, bases, and neutral compounds.
 

Whether you are analyzing whole blood, plasma, or serum, sample matrix components can interfere with analysis, decreasing both accuracy and sensitivity. Removing proteins through precipitation and filtration is a very common strategy for preventing problems, but with this procedure the sample still contains a high concentration of phospholipids. While LC-MS/MS analytical methods will not detect phospholipids if the ions they produce are not monitored, their presence can still affect the analytical results and the overall cleanliness of the instrument.

How to Avoid Phospholipid Signal Suppression

If phospholipids in the sample coelute with analytes of interest, they can affect target analyte ionization, which can cause suppression and lower overall analytical sensitivity. To illustrate signal suppression, we established a post-column infusion of nortriptyline and monitored the steady signal that the constant flow of analyte created. Then, we injected a sample of protein-precipitated plasma onto the column and monitored the presence of phospholipids as well as their effect on the nortriptyline signal. Figure 1A shows how certain phospholipids significantly reduced the nortriptyline response (by 38% in this case). In situations where a target analyte coelutes with phospholipids, use of internal standards can help account for phospholipid signal suppression and further method development can often eliminate the coelution. However, when phospholipid and protein removal can be done concurrently in the same process normally used to remove proteins alone, the question becomes “why try to design a method around something I can easily remove from my sample?”

Resprep PLR SPE products allow you to do just that: one simple SPE workflow removes proteins through precipitation and filtration, while phospholipids are selectively retained in an innovative sintered composite material. Figure 1B illustrates the effectiveness of removing phospholipids along with proteins using a Resprep PLR 96-well plate (cartridges are also available). Comparing again to a continuous post-column infusion of nortriptyline, we can see that the signal is suppressed with protein precipitation alone, but when the sample phospholipids are removed along with the proteins, the signal is no longer compromised. Higher accuracy and sensitivity can be obtained by avoiding phospholipid signal suppression.

Figure 1: Protein precipitation alone does not prevent phospholipid signal suppression (A), but simultaneous phospholipid and protein removal with Resprep PLR SPE eliminates this problem (B).

LC_GN0594

Excellent Recoveries for Wide Range of Compounds with No Method Development

Simultaneous phospholipid and protein removal using Resprep PLR SPE cartridges or 96-well plates can improve sensitivity by reducing phospholipid signal suppression, but its broad applicability offers an additional benefit: less time spent on method development. Simple to use and effective for a wide variety of compound chemistries, Resprep PLR SPE provides reliable cleanup without the need for compound-specific method development. As shown in the competitor comparison in Figure 2, good recoveries were obtained in plasma with a high degree of analytical precision for acidic, basic, and neutral compounds. Tight manufacturing controls ensure consistently strong performance, as demonstrated by the accurate and precise recovery results obtained in plasma for all three target compound categories across three independent lots (Table I).

Figure 2: Evaluation of Analyte Recovery for a Single 96-Well Plate by Manufacturer*

figure-article-GNAR3124-02.jpg

*Fortification levels given in Table I. Error bars represent ±%RSD.

 

Table I: Grand average percent recoveries for acids, bases, and neutral compounds across three different lots of Resprep PLR 96-well plates (3 plates per lot).

Compound
Class
Compound Fortification Level
(ng/mL)
Grand Average of
% Recoveries
(n = 787 wells)
Standard
Deviation
%RSD
Acids CBDA 150 94.1 9.3 9.9
Furosemide 250 105.3 17.2 16.4
Ketoprofen 125 105.4 7.3 6.9
Sulfadiazine 25 108.2 5.7 5.3
THCA 100 68.9 9.6 14.0
Bases Amphetamine 15 106.8 5.6 5.3
Fluvoxamine 50 104.3 6.4 6.1
Methadone 5 99.4 6.0 6.1
Nortriptyline 15 101.2 6.0 6.0
Propranolol 25 105.0 6.2 5.9
Neutrals CBN 100 87.7 9.1 10.4
Prednisolone 125 105.0 10.6 10.0

The reliable performance demonstrated here is due the robust design of Resprep PLR SPE products. A top frit is used to capture proteins, while the sorbent bed below is a specially designed porous polymer matrix that is co-sintered to silica particles that have bound ligands that retain phospholipids. The end result is a solid matrix for phospholipid and protein removal that—unlike loose sorbent beds—is not susceptible to channeling. Figure 3 shows the resulting performance: high levels of phospholipids are removed consistently across all tested wells in a representative 96-well plate. This means your target analytes can be effectively recovered and analytical accuracy will not be affected by phospholipid signal suppression. In addition, your instrument and overall productivity will benefit from not injecting high concentrations of phospholipids that will eventually reduce LC column lifetime and increase MS downtime as the ion source becomes contaminated.

Figure 3: Representative phospholipid removal performance for a typical Resprep PLR 96-well plate.

figure-article-GNAR3124-03.jpg

In conclusion, switching from protein precipitation alone to simultaneous phospholipid and protein removal with Resprep PLR SPE is an easy way to obtain more accurate, reliable results for clinically relevant substances in whole blood, plasma, or serum. The simple sample preparation process is effective for a wide range of analytes, so excellent results can be obtained for acids, bases, and neutral compounds without time and resources being spent on additional method development. In addition to removing interferences that could affect your data, Resprep PLR SPE ensures that less contamination is injected into your column and mass spectrometer, which results in less downtime for maintenance.

GNAR3124-UNV

Related Products

Resprep PLR SPE Products

View Product

Well Plates

View Product

Resprep VM-96 Vacuum Manifold for 96-Well Plates

View Product

Raptor C18 LC Columns (USP L1)

View Product

Raptor Biphenyl LC Columns (USP L11)

View Product